We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
Sort by:
- < Prev
- 1
- 2
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mauro
February 13, 2020
Turn on everything. It also turns on the heat element but does not turn the drum
For model number WED6400SW1
Hello Mauro, Thank you for the question. If everything is working as normal but the drum will not tumble, we suggest checking the Belt, PartSelect Number PS11746376. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Drive Belt
$87.04
In Stock
Garry
January 3, 2020
The sensing light comes on and pf shows up after unplugging it....
For model number WED6400SW1
Hello Garry,Thank you for your question. The "PF" error code means the dryer cycle was interrupted by a power failure, press and hold the START button to restart the dryer, and the error should go away. We hope this helps!
Was this helpful?
Thank you for voting!
Erik
January 19, 2020
This model was making a scrapping sound, now it won't start a cycle?
For model number WED6400SW1
Hello and thank you for writing.Sounds very much like you have a faulty pulley or belt, there is a maintenance kit PS373087 available for this model. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
Related Parts:
Maintenance Kit
$37.48
In Stock
Ron
January 29, 2023
Replaced thermostat and heat sensor still takes to Long to dry and can't adjust time for length of dry
For model number WED6400SW1
Hello Ron, Thank you for the question. We suggest testing the HI-Limit Thermostat and the Heat Element with a multimeter to check for the continuity. We hope this information helps!
Was this helpful?
Thank you for voting!
Related Parts:
Element, Heater
$179.81
In Stock
Thermostat, HI-Limit
Stacey
March 24, 2024
After my dryer run for a little while it starts to screech, it does this for about 10 minutes then stops. Have any suggestions on what is making it do this?
For model number WED6400SW1
Hi Stacey, thank you for your inquiry. We would recommend checking the drum support roller, part number PS11752609, to get to the root of the problem. Good luck with this repair!
Was this helpful?
Thank you for voting!
Related Parts:
Dryer Drum Support Roller
$22.69
In Stock
- < Prev
- 1
- 2
- Next >
Broken drive belt
Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section ... Read more off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.
Read less
Parts Used:
-
DENNIS from ALTOONA, FL
-
Difficulty Level:
A Bit Difficult
-
Total Repair Time:
1- 2 hours
-
Tools:
Nutdriver, Screw drivers
275 of 302 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer door catch broken
After a few years of slamming the dryer door (at least that is what my husband says), the catch on the dryer door broke. Using pliers (I used needle nose) squeeze the outer edges of the catch together (vertically). With it compressed, it should slide out easily. My husband had jacked with ours prior to the repair, so the broken piece i ... Read more n the door was actually sideways and would not fit through the hole. Using a screwdriver, I pushed that piece into the door (it lives in the door somewhere now). I was then able to slide out the rest of the old catch. Compress the new catch and insert it into the hole in the door. Push it in until it clicks into place. DONE! Happy Drying!
Read less
Parts Used:
-
Tammy from Clute, TX
-
Difficulty Level:
Really Easy
-
Total Repair Time:
Less than 15 mins
-
Tools:
Pliers
148 of 155 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bought motor, then bought blower wheel also
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! ... Read more Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!
Read less
Parts Used:
-
Daniel from Coatesville, PA
-
Difficulty Level:
Easy
-
Total Repair Time:
More than 2 hours
-
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
94 of 110 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
